회전용 고무 오일 씰 - Roatary Seal Brands

Ericks

고무 외경 타입( Outside Rubber Diameter )

RZV	Smaller sizes only for applications such as needle bearings and grease seal.

RGZV	Similar application as type RZV, but the outside surface has a ribbed design.

R	Rubber outer diameter with a carbon steel insert. Construction is in accordance with DIN 3760A and available in both metric and inch sizes.

RG	Ribbed outer rubber surface. With this system the thermal expansion of the housing is absorbed. This is used in automotive applications.

RST	Oil Seal with additional dust lip to prevent damage of sealing lip and to avoid the ingress of dust, dirt, water etc. into the system. Very commonly used in both metric and inch sizes.

RGST	Identical application as type RST, but the outside rubber surface has a ribbed design to absorb thermal expansion of the housing

RST-D

Seals pressures to 10 bar (1MPa) depending on the circumstances because it is more compact than type RST. It is recommended that our application engineers should be contacted.

RV	The helical spring is encapsulated in the seal. This is important when the seal has to be moved over almost the full shaft length, preventing both dislodgement of the spring and its contact with the medium to be sealed.

R-DUO

R type with two sealing lips, used for sealing two separate media. When the requested R-Duo type is not available, two R-types can be fitted back to back.

REX	This type has to be mounted on the shaft, and has the seal lip on the outside. It is used in wheel seal applications and is frequently used in centrifuges.

VITON-GR

Viton covered seal with completely encapsulated steel insert for high temperature and chemically aggressive applications; it is supplied with a stainless steel spring as standard. The Viton® used in the manufacture of Oil Seals is produced by DuPont Dow Elastomers.

VITON-GRST

Similar to Viton GR, but with an additional dust lip to prevent damage to the sealing lip and to prevent ingress of dust into the system. It is supplied with a stainless steel spring as standard

R-T	Oil Seal with a PTFE face bonded to the synthetic rubber element to reduce friction and heat development. Not available from stock. Its application is in Formula 1 engines.

RST-T

Similar to type R-T, but with additional dust lip. Not available from stock.

금속 외경 타입(Outside Metal Diameter)

MZV	Smaller sizes only for applications such as needle bearings and grease seal.

M	Metal cased standard Oil Seal with vulcanised sealing lips. This type is frequently replaced by type R.

MST	Similar to type M but with additional dust lip. Applications are the same as type RST, when the requested type is not available.

M-DUO

With two sealing lips, for sealing two separate media. Limited stock is available.

MEX	External sealing type, whereby the metal case is mounted on the shaft.

GV	Totally enclosed metal casing for extra reinforcement, and a vulcanised rubber sealing lip. It is widely employed for larger shaft diameters for example in heavy industry such as roller bearings.

GVPST

Similar to type GVP, but with additional dust lip.

VSS	Special type for sealing valve stems in engines. It is only produced on demand.

MR	Oil Seal commonly used in engines. Press fitting of a metal case combined with a better internal sealing rubber case

MRST	Similar as type MR with additional dust lip.

M-T	Oil Seal with a PTFE layer on the sealing lip to reduce friction and heat development. Its application is in Formula 1 engines. Not available from stock.

MST-T

Similar to type M-T but with additional dust lip. Not available from stock.

섬유 보강 고무 외경 타입( Outside Fabric Insert Reinforcement Diameter)

WR35	Outside surface with fabric insert reinforcement. Oil Seal without metal reinforcement. Split Seals also available. These are frequently installed back to back with a lock-in plate. They are available in NBR and FPM.

WR36	Similar to type WR35, but additional grooves on the back side for optimal grease supply to the sealing lips when back-to-back mounted.

WR37	Similar to type WR36, with grooves on the whole contour.

스플릿 씰( Split Seals)

Model 23 Garlock klozures

Model 23 Garlock klozuresSplit Seal, NBR, Mill Right, Viton®, Silicone; Wave spring; Diameter with ø 75 - ø1500 mm ; surface Speed up to 10 m/s

Fabric

NBR, Viton®, Silicone, also in Split Seal; In fabric reinforcement + RVS spring; diameter to ø 1200 mm; Model WR 35, 36, 37, 151, 154, 1635, 1636, 1637

헤비듀티 씰( Heavy-duty Seals)

Model 64 Garlock klozures

Model 64 Garlock klozuresHelical- and wave spring; NBR, Viton®, Silicone, Mill Right; Diameter ø 250 - ø 1800; Speed up to 35 m/s

Model 53 Garlock klozure

Model 53 Garlock klozureOnly wave spring RVS; NBR, Viton®, Silicone, Mill Right; Diameter ø 75 - ø 1000; Speed up to 15 m/s

Model 63 Garlock klozure

Model 63 Garlock klozureOnly wave spring RVS; NBR, Viton®, Silicone, Mill Right; Diameter ø6 - ø 75; Speed up to 15 m/s

Parker

Spring-Loaded Oil Retention Profiles

TB, SB – Metal case with ParKote� bore sealant or ground OD. Most common and economical.
TC, SC – Rubber covered OD for improved OD sealing and soft alloy housing.
TA, SA – Double case with ParKote� bore sealant or ground OD. Structural rigidity, blind shaft installation.
General purpose, spring-loaded design. Most commonly used for oil or grease retention. Double lip profiles have secondary lip for light dust and fluid exclusion.
NBR/FKM
Shaft Surface Speed
TB, TC, TA – Up to 2500 fpm (12.7 m/s)
SB, SC, SA – Up to 3200 fpm (16.3 m/s)
Maximum Pressure
0 to 7 psi (0 to 0.48 bar), depending on shaft speed
Shaft Size Range
0.250 to 10.000 inches (5 to 260 mm)

Springless Grease Retention Profiles

KB, VB – Metal case with ParKote� bore sealant or ground OD. Most common and economical.
KC, VC – Rubber covered OD. Improved OD sealing and soft alloy housing.
KA, VA – Double case with ParKote� bore sealant or ground OD. Structural rigidity, blind shaft installation.
TA, SA – Double case with ParKote� bore sealant or ground OD. Structural rigidity, blind shaft installation.
General purpose, spring-loaded design. Most commonly used for oil or grease retention. Double lip profiles have secondary lip for light dust and fluid exclusion.
NBR/FKM
Shaft Surface Speed
Up to 2000 fpm (10.2 m/s)
Maximum Pressure
0 to 7 psi (0 to 0.48 bar), depending on shaft speed
Shaft Size Range
0.250 to 6.000 inches (5 to 150 mm)

Dual Spring-Loaded Lip Profiles

DB – Metal case with ParKote� bore sealant or ground OD. Most common and economical.
DC – Rubber covered OD for improved OD sealing and soft alloy housing.
DA – Assembled case with ParKote� bore sealant or ground OD. Structural rigidity, blind shaft installation.
General purpose, spring-loaded design. Most commonly used for oil or grease retention. Double lip profiles have secondary lip for light dust and fluid exclusion.
NBR/FKM
Shaft Surface Speed
Up to 2000 fpm (10.2 m/s)
Maximum Pressure
0 to 7 psi (0 to 0.48 bar), depending on shaft speed
Shaft Size Range
0.250 to 6.000 inches (5 to 150 mm)

Medium Pressure Profiles

TDN3 – Rubber covered OD for improved OD sealing.
NSC4 – Rubber covered OD for improved OD sealing.
NTC4 – Rubber covered OD for improved OD sealing.
Shaft Surface Speed
Thru 4000 fpm (20.3 m/s)
Maximum Pressure
Up to 200 psi (13.7 bar), depending on design and shaft speed
Shaft Size Range
0.250 to 4.000 inches (5 to 100 mm)

Cassette Profiles

CB – Metal case with ParKote� bore sealant standard. CB design requires special installation tool.
CL, CH – Rubber covered OD for improved OD sealing and soft alloy housing.
Shaft Surface Speed
Up to 3200 fpm (16.3 m/s) depending on design
Maximum Pressure
0 to 7 psi (0 to 0.48 bar), depending on shaft speed
Shaft Size Range
0.500 to 14.000 inches (10 to 350 mm)

High Eccentricity Single Lip Profiles

SCE – Rubber covered OD for improved OD sealing in bores with minor imperfections and soft alloy housing.
SME – Metal case OD with rubber inside providing corrosion protection for inside of case.
SAE – Double case with ParKote� bore sealant standard. Inner case provides structural rigidity for large cross-sections. Guides shaft during installation.
Seal lip floats with shaft for more uniform lip loading during misalignment conditions. High runout conditions, up to 0.125 inch (3.18 mm) total eccentricity for oil or grease retention. Moderate speeds, dependent on misalignment.
Shaft Surface Speed
Up to 2500 fpm (12.7 m/s) depending on runout
Maximum Pressurebr/> 0 to 3 psi (0.20 bar), depending on shaft speed
Shaft Size Range
0.750 to 10.000 inches (20 to 260 mm)

Rotating Bore Profiles

OSB – Metal case with press fit ID.
OSC – Rubber covered ID for improved ID sealing.
OSA – Double case for structural rigidity.
Outside spring-loaded single lip design. For grease applications where bore rotates.
Shaft Surface Speed
Up to 2500 fpm (12.7 m/s) depending on runout
Maximum Pressure
0 to 7 psi (0 to 0.48 bar), depending on speed
Shaft Size Range
0.250 to 10.000 inches (5 to 260 mm)

PTFE/Elastomer Profiles

SBF – Metal case with ParKote� bore sealant standard. Most common and economical.
SCF – Rubber covered OD for improved OD sealing in bores with minor imperfections and soft alloy housing.
TBF – Metal case with ParKote� bore sealant standard. Most common and economical.
TCF – Rubber covered od for improved od sealing in bores with minor imperfections and soft alloy housing.
TN – The TN lip element is PTFE bonded to NBR and combines the low friction properties of PTFE with the flexibility of rubber.
The lip element is PTFE bonded to rubber and combines the low friction properties of PTFE with the flexibility of rubber. For dry running applications, higher speeds and enhanced chemical compatibility..
Shaft Surface Speed
Up to 5000 fpm (25.4 m/s) (TN – up to 2500 fpm [12.7 m/s])
Maximum Pressure
0 to 7 psi (0 to 0.48 bar), depending on shaft speed (TN – up to 10 psi [0.68 bar])
Shaft Size Range
0.500 to 10.000 inches (10 to 250 mm)

Wiper and Scraper Profiles

W – Metal case with ParKote� bore sealant or ground OD. Scraper lip profile.
WPC – Rubber covered OD for improved OD sealing. Wiper profile for grease retention in slow rotary and reciprocating applications.
WPR – Rubber covered OD for improved OD sealing.
General purpose rod wiper. For rotary and reciprocating shafts. Single lip, springless design. For heavy dust exclusion.
Shaft Surface Speed
Up to 2000 fpm (10.2 m/s) Rotary Up to 300 fpm (1.5 m/s) Reciprocating
Maximum Pressure
0
Shaft Size Range
0.375 to 10.000 inches (10 to 250 mm)

Clipper

LUP, LPD, LDS Profiles

LUP/LPD -General purpose spring-loaded single lip seal. Features nonmetallic composite OD for damage-free installation. LPD can be furnished with/without spring retainer feature.
LDS-General purpose double lip features nonmetallic composite OD for damage-free installation. LDS profile has a primary spring-loaded lip with a non-spring-loaded secondary lip for exclusion of light dust or contamination.
For oil and grease applications. Typical applications: electric motors, gearboxes, pumps, fans, runout table, work rolls, paper rolls, mixers and custom equipment.
Materials NBR/FKM
Shaft Surface Speed
LUP/LPD – Up to 3200 fpm (16.25 m/s)
LDS – Up to 2500 fpm (12.7 m/s)

LUPW, LPDW, LDSW Profiles

LUPW/LPDW – Spring-loaded single lip. Features nonmetallic composite OD for damage-free installation.
LDSW– Specialized double lip features nonmetallic composite OD for damage-free installation. Primary lip features molded-in springs for lubrication retention. Springless secondary lip for excluding light dust. Floating lip accommodates high misalignment conditions.
Most commonly used for oil or grease retention where high shaft misalignment is present. LUPW and LPDW accommodate misalignment by use of extended lip profile and may require a wider than normal bore depth to avoid interference of the lip. Type LDSW accommodates misalignment using a geometry that allows the lip to float with the shaft.
Materials NBR/FKM
Shaft Surface Speed
LUPW/LPDW – Up to 1000 fpm (5.1 m/s)
LDSW – 2500 fpm (12.7 m/s)

HP,MP Profiles

HP-High pressure with a fluoroelastomer sealing element, outer metal case, and a PTFE backup element for pressure. Standard with carbon steel case. Stainless steel and other alloys available.
MP – The standard MP is a rubber covered metal design, spring-loaded. Standard profile material FKM, other materials available upon request.
HP –Oil retention in rotary and oscillating pumps, compressors and custom equipment.
MP – Applications: for oil pumps, compressors and custom equipment.
Materials FKM
Shaft Surface Speed
HP – Up to 4000 fpm (20.3 m/s)
MP – Up to 4000 fpm (20.3 m/s)

OL Profile

Outside Lip (OL) – Spring-loaded outside lip. Non-metallic composite ID for tight press fit on shaft. Easy to install.

Materials NBR/FKM
Shaft Surface Speed
Up to 1000 fpm (5.1 m/s)

ST-LUP, ST-LPD Profiles

ST-LUP/ST-LPD – Spring-loaded single lip with heavy duty metal band inserted in composite OD. ST design features metal bands for absorbing shock load and greater bore retention. Spacer buttons are available for grease purging in applications requiring back-to-back sealing.
For heavy duty applications, work rolls, paper rolls, backup rolls and custom equipment.
Materials NBR/FKM
Shaft Surface Speed
Up to 3200 fpm (16.3 m/s)

TSS Profile

TSS-Features nonmetallic composite OD for damage free installation. Soft flexible lip provides low friction sealing friction sealing contact to give extended service life.

Typical applications: overhead cranes in steel mills, rotary drilling crown and travel blocks, draglines, hoists and elevators. Also used on mine cart wheels, flywheels and idler wheels.
Materials NBR/FKM
Shaft Surface Speed
Up to 2000 fpm (10.2 m/s)

DL Profile

TSS -Spring-loaded dual lip seal. Features nonmetallic composite OD for damage-free installation.

Dual spring-loaded lips are used when the separation of two fluids is required. The design is also used for high contamination applications in keeping out a dirty environment.
Materials NBR/FKM
Shaft Surface Speed
Up to 2000 fpm (10.2 m/s)

RPDT Profile

Spring-loaded single lip seal. Features tapered heel. Available in splits only.
Typical applications: pillow blocks.
Materials NBR
Shaft Surface Speed
Up to 2000 fpm (10.16 m/s)

P, H Profiles

P – Features nonmetallic composite OD for damage-free installation. The P wiper scraper lip extends outside the bore face.
H – Features nonmetallic composite OD for damage-free installation. Shallow cavity rod wiper designed for excluding dust and contamination.
P Wiper – Used in reciprocating applications.
H Wiper – Used in reciprocating and rotary applications.
Materials NBR/FKM
Shaft Surface Speed
P Wiper – Up to 300 fpm reciprocating (1.5 m/s)
H Wiper – Up to 300 fpm reciprocating (1.5 m/s), 2000 fpm rotary (10.2 m/s)

SS, SDS Profiles

SS– General purpose springless single lip seal. Features nonmetallic composite OD for damage-freeinstallation.
SDS – General purpose springless dual lip. Features nonmetallic composite OD for damage-free installation.
For grease retention and exclusion of light dust and fluids. Typical light duty applications.
Materials NBR/FKM
Shaft Surface Speed
Up to 2000 fpm (10.2 m/s)

TMAL, TMAS Profiles

TMAL – Features a stainless steel outer case containing a machined PTFE spring-loaded sealing element.
TMAS – Features a stainless steel outer case containing a machined PTFE non-spring-loaded sealing element.
TMAL and TMAS seals are designed for corrosive chemical service and FDA application.
Materials PTFE
Shaft Surface Speed
Up to 2500 fpm (12.7 m/s)

MIST Profile, LifeLine

MIST – Heavy duty spring-loaded single lip. Features nonmetallic composite OD for damage-free installation. MIST features molded-in spring to eliminate spring dumping.
STMIST – Heavy duty spring-loaded single lip. Features composite OD metal band reinforced construction for absorbing shock load and greater bore retention. STMIST features molded-in spring to eliminate spring dumping.
LifeLine– Spring-loaded single lip features heavy duty rubber covered metal insert. LifeLine features metal insert for absorbing shock load and greater bore retention. LifeLine features molded-in spring to eliminate spring dumping.
For heavy duty applications, work rolls, paper mills, backup rolls and custom equipment.
Materials NBR
Shaft Surface Speed
Up to 3200 fpm (16.3 m/s)

RUP, RPD Profiles

RUP/RPD – General purpose spring-loaded, single lip Features nonmetallic OD for damage-free installation. Available in solid or split.
Splits – Feature a positive bore retention and require no cover plate.
Typical applications: motors, gearboxes, pumps, fans, industrial rolls and custom equipment. Split seals are designed for applications where equipment is unable to be disassembled due to time constraints.
Materials NBR/FKM
Shaft Surface Speed
Up to 2000 fpm (10.2 m/s)

Merkel

M 19 MERKEL ROTOMATIC Rotary Shaft Seal

The M19 sealing ring consists of the elastomer rubber part with fabric reinforcement on the sliding surface and plastic anti-extrusion rings. The medium collects in the lubricating groove on the sliding surface and acts as a lubricant. This improves lubrication as well as reducing friction and frictional heat. This sealing element can withstand high pressures due to the anti-extrusion rings bridging the extrusion gap, and the seals can be fitted into recessed groove housings.
Rotary seals
Mills
Civil engineering
Link pins
General machinery
Steel production
Swivel / pivot seal
Pressure 400 bar/ 5800 PSI Shaft Surface Speed
0.2 m/s / .64 ft/s

M15 Rotary Shaft Seal

The M 15 is a double-acting seal set for pivoting motion in hydraulic systems. It has a profile ring and an O-ring as energizing elements, with inside sealing.
Rotary seals
Mills
Civil engineering
Link pins
General machinery
Steel production
Swivel / pivot seal
Pressure
400 bar/ 5800 PSI Shaft Surface Speed
0.5 m/s / 1.6 ft/s

M16 Rotary Shaft Seal

The M16 is a double-acting seal set for pivoting motion in hydraulic systems. It has a profile ring and an o-ring as energizing elements, with outside sealing.
Rotary seals
Mills
Civil engineering
Link pins
General machinery
Steel production
Swivel / pivot seal
Pressure
400 bar/ 5800 PSI
Shaft Surface Speed
0.5 m/s / 1.6 ft/s

RADIAMATIC R58 Shaft Seal

The R 58 Radiamatic shaft seal consists of a fabric reinforced section of sturdy design, firmly bonded to the rubber sealing lip. A helical tension spring assists radial contact pressure of the lip on the shaft. The shaft seals are installed with the sealing lip towards the outside (against water and sinter). The sealing lip, designed to have a higher contact pressure, ensures that only the required seal lubrication film is allowed to pass.
The R 58 Radiamatic shaft seal is designed for rolling mills and large gear mechanisms in heavy-duty machine construction.The R 58 has been developed to meet the special requirement of grease-lubricated bearing in rolling mill applications.
Pressure
0.5 bar/ 7.25 PSI Shaft Surface Speed
25 m/s / 80 ft/s

M17 Rotary Shaft Seal

The M17 sealing ring consists of a rubber part held firmly on both sides by fabric blocks, providing lubrication on the sliding surface. The fabric blocks prevent the seal from extruding into the sealing gap and, with the sealing element firmly held at the outside diameter, they prevent circumference distortion.
Rotary seals
Mills
Civil engineering
Link pins
General machinery
Steel production
Swivel/ pivot seal
Pressure
200 bar/ 2900 PSI
Shaft Surface Speed
0.1 m/s / .32 ft/s

RADIAMATIC R35 Shaft Seal

The Radiamatic 1635 shaft sealing rings are installed backto- back. A lantern ring is included so that lubricant can be forced between the sealing rings. They are used whenever adequate lubrication is ensured by the medium to be sealed.
Rotary seals
Mills
Civil engineering
Forging
Heavy-duty cylinders
General machinery
Steel production
Ship building
Wind turbines
Bearings
Pressure
0.5 bar/ 7.25 PSI
Shaft Surface Speed
25 m/s / 80 ft/s

RADIAMATIC R36 Shaft Seal

The Style 1636 shaft sealing rings are used when additional lubrication is necessary from the outside. These sealing rings are usually fitted in pairs back-to-back. This combination effectively seals the bearing lubricant and prevents the penetration of dust and splash water. The lubrication is fed between the sealing rings by means of the groove in the circumference of the sealing housing and the radial groove in the seal body.
Rotary seals
Mills
Civil engineering
Forging
Heavy-duty cylinders
General machinery
Steel production
Ship building
Wind turbines
Bearings
Pressure
0.5 bar/ 7.25 PSI
Shaft Surface Speed
25 m/s / 80 ft/s

RADIAMATIC R37 Shaft Seal

The Style 1637 shaft sealing rings are used when additional lubrication is necessary from the outside. These sealing rings are usually fitted in pairs back-to-back, and this combination effectively seals the bearing lubricant and prevents the penetration of dust and splash water. The sealing rings have a peripheral groove on the outer periphery in addition to the radial grooves.
Rotary seals
Mills
Civil engineering
Forging
Heavy-duty cylinders
General machinery
Steel production
Ship building
Wind turbines
Bearings
Pressure
0.5 bar/ 7.25 PSI
Shaft Surface Speed
25 m/s / 80 ft/s

NOK

NOK Seal Type Matrix (이미지 크게 보기)

Single Lip w/o Spring

Metal OD, Single PTFE Lip, Dual Case Oil Seal, No Spring

Metal O.D. design with an inner case design for greater structural rigidity. PTFE lip required for difficult sealing applications.

Metal OD, Single PTFE Lip, Dual Case Oil Seal, No Spring

Metal O.D. design with an inner case for greater structural rigidity. PTFE lip required for difficult sealing applications.

Metal OD, Single PTFE Lip, Dual Case Oil Seal, No Spring

Metal O.D. design with an inner case for greater structural rigidity. PTFE lip required for difficult sealing applications. This seal has additional special features.

Metal OD, Single Lip, Dual Case Oil Seal, No Spring

Metal O.D. design with an inner case for greater structural rigidity. PTFE lip required for difficult sealing applications.

Type VB/B10F Oil Seal

Metal O.D. with fluid side rubber covered. Most commonly used for sealing grease or other viscous fluids or as a dust excluder.

Metal OD, Single Lip Oil Seal, No Spring

Metal O.D. with fluid side rubber covered. Most commonly used for sealing grease or other viscous fluids or as a dust excluder.

Metal OD, Single Lip Oil Seal, No Spring

Grease or viscous fluid retention or dust exclusion, Metal O.D., No Spring, Single Lip. Mainly used in low-duty applications.

Metal OD, Single Lip Oil Seal, No Spring with PTFE Lip-Special

Grease or viscous fluid retention or dust exclusion, Metal O.D., No Spring, Single Lip with PTFE. Mainly used in low-duty applications.

Metal OD, Single Lip Oil Seal, No Spring-Special Feature

Grease or viscous fluid retention or dust exclusion, Metal O.D., No Spring, Single Lip. Mainly used in low-duty applications. This seal has additional special features.

Metal OD, Single Lip Oil Seal, No Spring-Special Feature

Grease or viscous fluid retention or dust exclusion, Metal O.D., No Spring, Single Lip. Mainly used in low-duty applications. This seal has a flange and additional special features.

Metal OD, Single Lip Oil Seal, No Spring-Special Feature

Grease or viscous fluid retention or dust exclusion, Metal O.D., No Spring, Single Lip. Mainly used in low-duty applications. This seal has a flange and additional special features.

Metal OD, Mulit- Lip Oil Seal, No Spring-Special Feature

Grease or viscous fluid retention or dust exclusion, Metal O.D., No Spring, Single Lip. Mainly used in low-duty applications. This seal has an additional side lip.

Metal OD, Single Lip Oil Seal, No Spring with PTFE Lip-Special

Metal O.D. with fluid side rubber covered. Most commonly used for sealing grease or other viscous fluids or as a dust excluder. Metal O.D., No Spring PTFE on main lip

Metal OD, Single Lip, Oil Seal-Special Feature

Metal O.D. with fluid side rubber covered. Most commonly used for sealing grease or other viscous fluids or as a dust excluder.

Rubber OD, Single Lip Oil Seal, No Spring

Economic design for grease or viscous fluid retention or as a dust excluder, Rubber OD, No Spring, Single Lip. Mainly used in low-duty applications.

Rubber OD, Single Lip Oil Seal, No Spring-Special Feature

Economic design for grease or viscous fluid retention or as a dust excluder, Rubber OD, No Spring, Single Lip. Mainly used in low-duty applications. This seal also has a flange.

Rubber OD, Single Lip Oil Seal, No Spring-Special Feature

Economic design for grease or viscous fluid retention or as a dust excluder, Rubber OD, No Spring, Single Lip. Mainly used in low-duty applications. This seal also has a flange and added special features.

Rubber OD, Multi- Lip Oil Seal, No Spring-Special Feature

Economic design for grease or viscous fluid retention or as a dust excluder, Rubber OD, No Spring, Single Lip. Mainly used in low-duty applications. This seal has an additional side lip and special features added.

Rubber OD, Multi- Lip Oil Seal, No Spring with PTFE Lip-Special

Economic design for grease or viscous fluid retention or as a dust excluder, Rubber OD, No Spring, Single Lip with PTFE. Mainly used in low-duty applications.

Rubber OD, Multi- Lip Oil Seal, No Spring with PTFE Lip-Special

Economic design for grease or viscous fluid retention or as a dust excluder, Rubber OD, No Spring, Single Lip with PTFE. Mainly used in low-duty applications. This seal has additional special features.

Rubber OD, Single Lip Oil Seal, No Spring-Special Feature

Economic design for grease or viscous fluid retention or as a dust excluder, Rubber OD, No Spring, Single Lip. Mainly used in low-duty applications.